Bike Rack Builder
Shopping list
Any straight studs work. If the rack lives outside or on a wet garage slab, buy pressure-treated for the two floor rails at least.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8′ SPF board | 7 | $3.50 | $24.50 |
| #9 × 3″ construction screws, 1-lb box (about 48) | 1 | $10.00 | $10.00 |
| #9 × 2½″ construction screws, 1-lb box (about 32, for the fins: a 3″ screw would come through into the slot) | 1 | $10.00 | $10.00 |
| Sandpaper, 120 grit, 5-pack | 1 | $5.00 | $5.00 |
| Total | $49.50 |
Tools: miter saw (or circular saw and speed square), drill/driver, tape, square, clamps.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
7 boards88% yieldEach slot is two 2×4 fins that climb from the front rail to a back post. The wheel rolls over the front rail, settles on the floor behind it and stops against the top rail; the fins pinch the tire low at the front and just below hub height at the back. Sized for 20″ to 29″ wheels. At 18″ spacing or less, neighbouring handlebars overlap, as on any bike rack: turn the bars a little as you park.
- 1
Shopping list
Any straight studs work. If the rack lives outside or on a wet garage slab, buy pressure-treated for the two floor rails at least.
Item Qty Each Total 2×4×8′ SPF board 7 $3.50 $24.50 #9 × 3″ construction screws, 1-lb box (about 48) 1 $10.00 $10.00 #9 × 2½″ construction screws, 1-lb box (about 32, for the fins: a 3″ screw would come through into the slot) 1 $10.00 $10.00 Sandpaper, 120 grit, 5-pack 1 $5.00 $5.00 Total $49.50 Tools: miter saw (or circular saw and speed square), drill/driver, tape, square, clamps.
- 2
Cut list
Fins get a 17° cut on both ends, parallel, so both ends come out plumb when the fin climbs from the front rail to the post. Length is measured along either edge.
Tag Part Length Qty Cut R Floor rail (front, back) and top rail 72″ 3 square P Post 14″ 8 square F Fin 29¼″ 8 17° both ends, parallel (plumb ends) K Front block (sits on edge) 3½″ 8 square Round the top front corner of every fin with a sander or a few rasp strokes. It's where a spoke or a shin finds it. - 3
Lay out the floor rails
Lay the two floor rails flat, parallel, 28″ outside to outside. Mark the center of each slot on both rails: first at 9″ from the end, then every 18″.
From each center mark 1¼″ each side for the fins, then 1½″ beyond that for the posts. Square the marks across both rails so the slots run straight.
- 4
Posts and front blocks
8 posts stand on the back rail, flush with its back edge, just outside each slot's fin marks. A 3½″ block sits on edge on the front rail in line with each post, grain running front to back, flush with the rail's front edge.
- Predrill and drive two 3″ screws up through the rail into the end of each post and into the edge of each block.
- Check each post plumb with a square off the rail. Don't trust your eye at this height.
- 5
Top rail
Lay the top rail flat across the post tops, ends flush with the floor rails. Two 3″ screws down into every post.
The back is now a rigid ladder; the fins will tie the front rail to it.
- 6
Fit the fins
Each fin runs from the front rail up to its post, lying against the inside faces of the front block and the post, its low end on the front rail and its bottom edge 10″ off the floor at the back. A pair of fins makes one slot, 2½″ apart.
- Cut a scrap to the slot width and use it as a spacer between the two fins of a pair.
- Clamp the fin to the post and block, check the slot width at the front and back, then two 2½″ screws through the post into the fin.
- Two more 2½″ screws through the front block into the fin. Not 3″: post plus fin is exactly 3″ thick, and a point sticking into the slot finds a tire.
Roll a bike in before you do the rest. If the tire rubs, open the slot ⅛″; if the bike leans more than a few degrees, close it. - 7
Done
4 slots. Roll the front wheel in over the front rail until the tire touches the top rail: it settles on the floor between the two floor rails, so the bike can't roll back out on its own, and the fins hold the tire on both sides. Neighbouring handlebars overlap at this spacing; turn the bars a little as you park.
On a smooth floor, a few strips of rubber shelf liner under the rails stops the rack creeping when you yank a bike out.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
7 boards88% yieldEach slot is two 2×4 fins that climb from the front rail to a back post. The wheel rolls over the front rail, settles on the floor behind it and stops against the top rail; the fins pinch the tire low at the front and just below hub height at the back. Sized for 20″ to 29″ wheels. At 18″ spacing or less, neighbouring handlebars overlap, as on any bike rack: turn the bars a little as you park.