Bookshelf & Media Console Builder
Shopping list
Pick the straightest, driest studs you can find; the posts are visible and a bowed one shows. A full bookshelf weighs a few hundred pounds. The front stretchers keep shelves from sagging into a smile.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8 stud, kiln-dried (posts, rungs, stretchers) | 6 | $3.98 | $23.88 |
| ¾″ × 4×8 plywood, sanded (rip to 12″) | 1 | $54.98 | $54.98 |
| ½″ × 4×8 plywood, sanded (back) | 1 | $39.98 | $39.98 |
| #9 × 2½″ construction screws, 1-lb box (~80) (about 72) | 1 | $10.48 | $10.48 |
| #8 × 1⅝″ wood screws, 100-pack (shelves, back · about 77) | 1 | $7.98 | $7.98 |
| Wood glue, 8 oz | 1 | $4.98 | $4.98 |
| Furniture anti-tip kit (L-bracket + wall screws) | 1 | $8.98 | $8.98 |
| Stain or paint, 1 qt + poly, 1 qt | 1 | $32.98 | $32.98 |
| Total | $184.24 |
Tools: miter saw or circular saw with a speed square, straightedge guide for ripping ply, drill/driver, countersink bit, clamps, square, stud finder, 120/180 sandpaper.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
6 boards97% yieldSheet goods
- S Shelf: 4 × 33″ × 12″
- T Top: 1 × 36″ × 12″
- B Back panel, ½″ ply: 1 × 72″ × 36″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
Each side is a ladder: two 2×4 posts with 2×4 rungs on the inside face. Shelves sit on the rungs and a front 2×4 stretcher, so nothing is notched and nothing hangs on screws alone. A glued ½″ plywood back squares the whole thing. Anchor it to a wall stud, always.
- 1
Shopping list
Pick the straightest, driest studs you can find; the posts are visible and a bowed one shows. A full bookshelf weighs a few hundred pounds. The front stretchers keep shelves from sagging into a smile.
Item Qty Each Total 2×4×8 stud, kiln-dried (posts, rungs, stretchers) 6 $3.98 $23.88 ¾″ × 4×8 plywood, sanded (rip to 12″) 1 $54.98 $54.98 ½″ × 4×8 plywood, sanded (back) 1 $39.98 $39.98 #9 × 2½″ construction screws, 1-lb box (~80) (about 72) 1 $10.48 $10.48 #8 × 1⅝″ wood screws, 100-pack (shelves, back · about 77) 1 $7.98 $7.98 Wood glue, 8 oz 1 $4.98 $4.98 Furniture anti-tip kit (L-bracket + wall screws) 1 $8.98 $8.98 Stain or paint, 1 qt + poly, 1 qt 1 $32.98 $32.98 Total $184.24 Tools: miter saw or circular saw with a speed square, straightedge guide for ripping ply, drill/driver, countersink bit, clamps, square, stud finder, 120/180 sandpaper.
- 2
Cut list
Rip the ¾″ plywood into 12″ strips, then crosscut shelves. Rungs are the full 12″ depth so they cover both posts.
Tag Part Length Qty Cut P Post 71¼″ 4 square R Rung 12″ 10 square F Front stretcher 30″ 5 square S Shelf (12″ wide) 33″ 4 square T Top (12″ wide) 36″ 1 square B Back panel, ½″ ply (36″ wide) 72″ 1 square Gang-cut the four posts together with a stop block. Equal posts are what make the top sit flat. - 3
Build the side ladders
Lay two posts on the bench 5″ apart (outer faces 12″). Screw a rung across their inside face at every shelf height: the rung's top edge is where the shelf's bottom lands.
- Rung tops at 3½″, 20½″, 37⅜″, 54⅜″, 71¼″ from the floor. The bottom rung sits on the floor; the top rung is flush with the post tops.
- Glue plus two 2½″ screws into each post, pilot holes near the ends.
Build the second ladder directly on top of the first, clamped, so the rungs land at identical heights. - 4
Front stretchers
Stand the ladders up, rungs facing in, and run a 30″ 2×4 on edge between the front ends of each pair of rungs, flush with the front.
Two 2½″ screws through each rung into the stretcher end. This is the beam that keeps the shelf from sagging.
Check: the diagonals of the front face are equal. Rack it square now; the back locks it in Step 7. - 5
Shelves
Drop in 4 shelves (33″ × 12″) onto the rungs and stretchers. Glue on the rungs and stretcher, then 1⅝″ screws down through the shelf: two into each rung and one every 8″ into the stretcher.
Band or sand the front ply edge before this if you're painting; it's easier flat.
- 6
Top
The 36″ top caps the post ends and the top rungs. Glue, then drive 2½″ screws down into each post and rung, countersunk.
Ease the front edge with sandpaper or a roundover bit.
- 7
Back panel
Lay the unit face down. Glue and screw the ½″ back to every post, rung and shelf edge with 1⅝″ screws every 8″.
The back is what keeps it from racking side to side. Square the case before the first screw goes in.
- 8
Anchor to the wall
72″ tall and top-heavy with books: this tips over if someone climbs it or pulls on a shelf. Anchor it.
- Find a stud behind the unit.
- Screw the L-bracket to the top (or the back of the top rung) and into the stud with the kit's 2½″ screws.
- If a baseboard holds the unit off the wall, don't pull the top back to meet the wall. Put a spacer block as thick as the baseboard behind the top at the stud and run the bracket screw through it, so the unit stays plumb.
Never skip the anchor. Tip-overs injure thousands of kids a year; a $9 bracket prevents them. - 9
Done
Bookshelf, 36″ × 72″ × 12″, 5 shelves with 16¼″ between them.
Sand to 180, then stain and two coats of wipe-on poly, or prime and paint. Let it cure a few days before loading.
Load the heaviest books on the bottom two shelves; it keeps the center of gravity low.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
6 boards97% yieldSheet goods
- S Shelf: 4 × 33″ × 12″
- T Top: 1 × 36″ × 12″
- B Back panel, ½″ ply: 1 × 72″ × 36″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
Each side is a ladder: two 2×4 posts with 2×4 rungs on the inside face. Shelves sit on the rungs and a front 2×4 stretcher, so nothing is notched and nothing hangs on screws alone. A glued ½″ plywood back squares the whole thing. Anchor it to a wall stud, always.