Console Table Builder
Shopping list
Furniture lives or dies on straight stock. Sight down every board and take the ones with tight, flat grain; for the top, pick 2 2×6s from the same stack so the color matches. Let them sit indoors a week before cutting.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8′ stud, untreated SPF | 3 | $3.50 | $10.50 |
| 2×6×8′, select / premium | 3 | $6.50 | $19.50 |
| 2½″ coarse pocket-hole screws, 100-ct | 1 | $8.00 | $8.00 |
| Figure-8 tabletop fasteners, 8-pack (plus ⅝″ #8 screws (usually included)) | 1 | $7.00 | $7.00 |
| #8 × 2½″ wood screws, small box (shelf boards) | 1 | $6.00 | $6.00 |
| Wood glue, 16 oz | 1 | $7.00 | $7.00 |
| Stain + wipe-on poly, 1 qt each | 1 | $30.00 | $30.00 |
| Felt furniture pads | 1 | $5.00 | $5.00 |
| Total | $93.00 |
Tools: miter saw, pocket-hole jig, drill/driver, 4 bar or pipe clamps (long enough for the top), Forstner bit for the figure-8s, random-orbit sander 80–220 grit. A table saw or jointer helps square the top edges.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×6 × 8′
2 boards74% yield2×4 × 8′
3 boards76% yieldThe top overhangs 1″ at each end and ¾″ front and back. 2×6 is 5½″ wide and 2×8 is 7¼″ after the factory eased edges; plan on losing ⅛″ per joint if you rip them square. Prices are per 8′ board at the price you enter; 2×8 is estimated at 1.55× a 2×6.
- 1
Shopping list
Furniture lives or dies on straight stock. Sight down every board and take the ones with tight, flat grain; for the top, pick 2 2×6s from the same stack so the color matches. Let them sit indoors a week before cutting.
Item Qty Each Total 2×4×8′ stud, untreated SPF 3 $3.50 $10.50 2×6×8′, select / premium 3 $6.50 $19.50 2½″ coarse pocket-hole screws, 100-ct 1 $8.00 $8.00 Figure-8 tabletop fasteners, 8-pack (plus ⅝″ #8 screws (usually included)) 1 $7.00 $7.00 #8 × 2½″ wood screws, small box (shelf boards) 1 $6.00 $6.00 Wood glue, 16 oz 1 $7.00 $7.00 Stain + wipe-on poly, 1 qt each 1 $30.00 $30.00 Felt furniture pads 1 $5.00 $5.00 Total $93.00 Tools: miter saw, pocket-hole jig, drill/driver, 4 bar or pipe clamps (long enough for the top), Forstner bit for the figure-8s, random-orbit sander 80–220 grit. A table saw or jointer helps square the top edges.
- 2
Cut list
Every cut is square. Cut the four legs together with a stop block; a table with one short leg is the classic mistake. Then rip or plane the rounded factory edges off the top boards where they meet, so the joints close tight.
Tag Part Length Qty Cut A Leg 28½″ 4 square B Front / back apron 39″ 2 square C End apron 6½″ 2 square E End stretcher 6½″ 2 square F Shelf board 46″ 1 square G Top board 48″ 2 square; joint the mating edges Drill all the pocket holes before any assembly: two in each end of every apron and stretcher, on the inside face, plus a few along the aprons if you skip the figure-8s. - 3
Build the two end frames
Stand two legs on edge on a flat bench, wide faces toward each other and 9½″ apart outside to outside. Lay an end apron (C) flat on the bench between them, pocket holes up, flush with the leg tops; the side on the bench becomes the flush outside face. Glue and two pocket screws each end.
Check square with a framing square, then make the second one. Mirror the pocket holes so they face in on both.
- 4
Join with the long aprons
Stand the end frames up and pocket-screw the front and back aprons (B, 39″) between the legs, flush at the top and flush with the outside face.
Measure the diagonals across the top. Push the long corners together until they match, then clamp a diagonal brace across the legs while the glue sets.
- 5
Lower shelf
Pocket-screw an end stretcher (E) between each pair of legs, 6″ off the floor. They carry the shelf and stop the legs racking.
Lay the shelf board across the stretchers, flush at the ends, centered. Screw down through each board into the stretchers, two 2½″ screws per end, pilot-drilled and countersunk (or counterbored and plugged).
- 6
Glue up and fasten the top
Glue the 2 top boards edge to edge (do this first, the day before). Alternate clamps over and under, snug not crushing, and wipe the squeeze-out after 20 minutes.
- Scrape and sand the joints flush, 80 then 120 grit.
- Center the top: 1″ overhang at each end and about ¾″ front and back (a hair less if you jointed the edges).
- Fasten with figure-8 fasteners in the apron tops, two per long apron and one per end. They let the top move with the seasons; screwing it rigid will crack it.
- 7
Done
A 48″ × 11″ console, 30″ tall. Ease all edges, sand to 220, then stain and three coats of wipe-on poly. Felt pads under the feet.
Pine blotches under stain. Wipe on a pre-stain conditioner first, or use a gel stain.A 30″ table on a 9½″-deep base can tip if a child climbs or pulls on it. In a house with kids, add a furniture strap from the back apron to a wall stud.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×6 × 8′
2 boards74% yield2×4 × 8′
3 boards76% yieldThe top overhangs 1″ at each end and ¾″ front and back. 2×6 is 5½″ wide and 2×8 is 7¼″ after the factory eased edges; plan on losing ⅛″ per joint if you rip them square. Prices are per 8′ board at the price you enter; 2×8 is estimated at 1.55× a 2×6.