Deck Box Builder
Shopping list
A pressure-treated 2×4 frame skinned with cheap fence pickets. Cedar or PT for anything outdoors; untreated is fine under a covered patio.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8 PT, frame and lid cleats | 7 | $4.98 | $34.86 |
| 6′ dog-ear fence picket, ⅝″ × 5½″, cedar or PT | 17 | $2.98 | $50.66 |
| 6″ T-hinge, exterior (black or galvanized) | 2 | $6.98 | $13.96 |
| Lid support stay (soft-close or friction) (holds the lid open; no slamming on fingers) | 1 | $11.98 | $11.98 |
| #9 × 2½″ exterior screws, 1-lb box (about 46) | 1 | $10.98 | $10.98 |
| #9 × 3″ exterior screws, 1-lb box (about 22) | 1 | $10.98 | $10.98 |
| #8 × 1⅝″ exterior screws, 1-lb box (about 209: skin, floor, lid and hinges) | 2 | $9.98 | $19.96 |
| Total | $153.38 |
Tools: miter or circular saw, drill/driver, tape, speed square, clamps; a table saw or circular saw with a rip guide for the top skin row.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
7 boards81% yieldPicket × 6′
17 boards81% yieldA 2×4 frame carries the load; the skin just keeps weather out. Gaps between skin boards let it breathe, so it is a ventilated box, not a waterproof one: keep cushions in a storage bag, or staple 6-mil plastic under the lid slats, if it lives out in the rain. Pickets are ⅝″ × 5½″ dog-ear fence pickets with the dog-ear cut off.
- 1
Shopping list
A pressure-treated 2×4 frame skinned with cheap fence pickets. Cedar or PT for anything outdoors; untreated is fine under a covered patio.
Item Qty Each Total 2×4×8 PT, frame and lid cleats 7 $4.98 $34.86 6′ dog-ear fence picket, ⅝″ × 5½″, cedar or PT 17 $2.98 $50.66 6″ T-hinge, exterior (black or galvanized) 2 $6.98 $13.96 Lid support stay (soft-close or friction) (holds the lid open; no slamming on fingers) 1 $11.98 $11.98 #9 × 2½″ exterior screws, 1-lb box (about 46) 1 $10.98 $10.98 #9 × 3″ exterior screws, 1-lb box (about 22) 1 $10.98 $10.98 #8 × 1⅝″ exterior screws, 1-lb box (about 209: skin, floor, lid and hinges) 2 $9.98 $19.96 Total $153.38 Tools: miter or circular saw, drill/driver, tape, speed square, clamps; a table saw or circular saw with a rip guide for the top skin row.
- 2
Cut list
Tag Part Length Qty Cut LG Leg, 2×4 (4 corners + 2 mid stud) 21⅞″ 6 square R1 Long rail, 2×4 on edge (the legs lap its outside face) 48″ 4 square R2 End rail, 2×4 on edge (between the long rails) 18″ 4 square F Floor slat, 1×6 flat 21″ 8 square S1 Side skin, long, 1×6 48″ 6 square S2 Side skin, end, 1×6 25¼″ 6 square S3 Side skin, long, top row, 1×6 48″ 2 rip to 4⅛″ wide S4 Side skin, end, top row, 1×6 25¼″ 2 rip to 4⅛″ wide D1 Lid cleat, 2×4 flat (front, back and center) 50¼″ 3 square D2 Lid slat, 1×6 flat, across the depth 25¾″ 9 square The top skin row is ripped to 4⅛″ so it finishes flush with the leg tops. Rip it from the edge that will face down, so the factory edge is on top. - 3
Two rail frames
The frame is two identical rectangles, one for the bottom and one for the top. For each, stand two 48″ long rails on edge and fit two 18″ end rails between them, flush with the ends. Each rectangle is 48″ × 21″ outside.
- Two 3″ screws through the long rail into each end of the end rails. Pre-drill so the end grain doesn't split.
- Check each rectangle is square: the two diagonals should match within ⅛″.
- 4
Legs and mid studs
Set the bottom rectangle on 1″ scraps on a flat floor. Stand a 21⅞″ leg at each corner, its wide face flat against the outside of the long rail, its outer edge flush with the end of the rail and its foot on the floor. The legs make the box 24″ deep.
- Clamp, then three 2½″ screws through each leg into the rail (leg and rail are 3″ together, so they won't poke through).
- Lower the top rectangle between the legs until it is flush with the leg tops (clamp a scrap across two leg tops to hang it from), check the legs are plumb, and screw it the same way.
- Add a mid stud on each long side, same length as the legs and screwed to both rails the same way, centered 24″ from one end. The long rails sit 1½″ behind the skin, so the skin boards fasten only to the legs and these studs.
Check: diagonals across the top opening should match. Rack it square before the floor goes in. - 5
Floor
Lay the 8 floor slats across the depth, resting on the bottom long rails, about ⅛″ apart so water drains. Two 1⅝″ screws per end into the rail.
- 6
Skin the sides
Start ½″ above the leg bottoms (so the skin stays off a wet deck) and work up with a ¼″ spacer: long sides first, then the ends lapping over their ends so the end grain is hidden.
- Long sides: two 1⅝″ screws through each board into each leg and mid stud.
- Ends: two screws through each board into the edge of the leg at each end, plus two into the end rail on the rows that cross one.
- The top row is the ripped 4⅛″ board, flush with the leg tops.
- 7
Lid
Lay three 50¼″ 2×4 lid cleats flat and parallel, 25¾″ outside to outside, with the third centered between them. Screw the 9 lid slats across them (25¾″ long, about ⅛″ apart), ends flush with the outer edges of the outer cleats, two 1⅝″ screws into every cleat.
The lid overhangs the box ½″ at the front and at both ends so it sheds rain past the skin; at the back it is flush with the skin, which is where the hinges go. The center cleat keeps the slats from flexing when someone sits on it.
- 8
Hinges and done
Set the lid on: back edge flush with the back skin, ½″ overhang at each end. Mount the two T-hinges on the back, one over each back leg, with the hinge pin right on the seam under the lid: the short leaf goes on the edge of the lid's back cleat, the 6″ strap runs straight down the skin over the leg.
- Use 1⅝″ screws, not the short ones in the hinge pack: the strap screws have to go through the skin and bite the leg.
- The lid swings up and back about 2″ past the back of the box, so leave 3″ between the box and a wall.
- Add the lid stay on one end so the lid holds open and can't slam.
The gaps in the floor let rain that gets in drain straight out; don't line the bottom with anything that holds water. Never add a latch: a child must always be able to push the lid open from inside.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
7 boards81% yieldPicket × 6′
17 boards81% yieldA 2×4 frame carries the load; the skin just keeps weather out. Gaps between skin boards let it breathe, so it is a ventilated box, not a waterproof one: keep cushions in a storage bag, or staple 6-mil plastic under the lid slats, if it lives out in the rain. Pickets are ⅝″ × 5½″ dog-ear fence pickets with the dog-ear cut off.