Garage Shelving Builder
Shopping list
Sight down every stud and reject anything bowed or twisted: uprights especially, since a crooked one throws the whole ladder out. Have the store rip the plywood into 23⅞″ strips if you don't own a track or table saw; it also fits in the car.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8′ SPF board | 14 | $3.50 | $49.00 |
| ¾″ plywood, 4×8 sheet (BC or sanded) (8 decks) | 2 | $52.00 | $104.00 |
| #9 × 3″ construction screws, 1-lb box (about 48) | 1 | $10.00 | $10.00 |
| #9 × 2½″ construction screws, 1-lb box (about 48) | 1 | $10.00 | $10.00 |
| #8 × 1⅝″ wood screws, 1-lb box (about 64) | 1 | $9.00 | $9.00 |
| #10 × 3½″ structural wood screws, 20-pack (top back rail into the wall studs) | 1 | $11.00 | $11.00 |
| Total | $193.00 |
Tools: miter saw or circular saw with a speed square, drill/driver with T25 bit, ⅛″ drill bit for pilots, tape, 4′ level, clamps, stud finder.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
14 boards91% yieldSheet goods
- P Shelf deck, ¾″ plywood: 8 × 30⅝″ × 23⅞″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
Ladders every ≤48″ carry two long rails per shelf, screwed across the wide faces of the uprights; each plywood deck sits between the uprights on those rails, so nothing gets notched. Depth is overall, rail face to rail face. Screw the top back rail to the wall studs: a loaded shelf unit is top-heavy.
- 1
Shopping list
Sight down every stud and reject anything bowed or twisted: uprights especially, since a crooked one throws the whole ladder out. Have the store rip the plywood into 23⅞″ strips if you don't own a track or table saw; it also fits in the car.
Item Qty Each Total 2×4×8′ SPF board 14 $3.50 $49.00 ¾″ plywood, 4×8 sheet (BC or sanded) (8 decks) 2 $52.00 $104.00 #9 × 3″ construction screws, 1-lb box (about 48) 1 $10.00 $10.00 #9 × 2½″ construction screws, 1-lb box (about 48) 1 $10.00 $10.00 #8 × 1⅝″ wood screws, 1-lb box (about 64) 1 $9.00 $9.00 #10 × 3½″ structural wood screws, 20-pack (top back rail into the wall studs) 1 $11.00 $11.00 Total $193.00 Tools: miter saw or circular saw with a speed square, drill/driver with T25 bit, ⅛″ drill bit for pilots, tape, 4′ level, clamps, stud finder.
- 2
Cut list
Label the piles with painter's tape: U, R, L, P. Each ladder is 21″ front to back (two 1½″ uprights plus the 18″ rung); the rails add the last 3″. Cut one rung, check it, then clamp a stop block and cut the rest.
Tag Part Length Qty Cut U Upright 72″ 6 square R Rung (ladder, front to back) 18″ 12 square L Long rail, front/back 72″ 8 square P Shelf deck, ¾″ plywood (23⅞″ wide) 30⅝″ 8 square Mark rung heights on every upright from the same end, before assembly. The top of each rung sits at: 7½″, 28¾″, 50″, 71¼″. - 3
Build the first ladder
A ladder is two uprights joined by 4 rungs. Stand two uprights on edge on a flat floor (3½″ faces vertical, the rung marks facing each other), 18″ apart. A rung is your spacer.
- Lay each rung flat between them, its upper edge on your mark, flush with the uprights on the floor side.
- Clamp, drill two ⅛″ pilot holes through the upright into each rung end (2″ apart along the upright, ¾″ up from the floor so they hit the middle of the rung), add a bead of glue, and drive two 3″ screws per rung end.
Check: measure both diagonals; they should match within ⅛″. Every ladder after this copies the first one, errors included. - 4
Build the other 2 ladders
Repeat for the other 2 ladders. Lay the next pair of uprights directly on the first ladder and transfer the rung lines so all shelves come out level.
Stack finished ladders flat until you stand them up; leaning them against a wall overnight is how they get a twist.
- 5
Stand up and add the bottom rails
Stand the ladders a couple of feet out from the wall so you can work behind them, 30¾″ clear between uprights (34¼″ on center), rungs all on the same side.
- Clamp the front bottom rail across the wide faces of the front uprights, its top flush with the bottom rung tops and its ends flush with the outside of the end ladders.
- Level it, then two 2½″ screws side by side into each upright (rail plus upright is exactly 3″ thick, so a 3″ screw would poke out the far side). Repeat on the back.
Until the first two rails are on, the ladders want to fold. A helper for ten minutes beats chasing it alone. - 6
Add the remaining rails
Install the other 6 rails the same way, working bottom to top, front then back. Rail top flush with the rung top, two 2½″ screws per upright crossing. The top pair sits ¾″ below the upright tops, so the top deck finishes flush with them.
Check plumb on the end uprights with a 4′ level before you set the top pair; once the top rails are on, the frame is locked.
- 7
Tie it to the wall
72″ tall and loaded, this unit tips forward if someone climbs it or yanks a stuck bin, so it gets screwed to the wall now, while the frame is still light and open. Slide it back until the back rails touch the wall, then find the studs behind the top back rail with a stud finder.
- Drive two #10 × 3½″ structural screws through the top back rail into every stud it crosses, one high and one low.
- At least two studs; drywall anchors don't count. If the floor slopes and the rail stands off the wall, shim the gap at each screw so you don't bow the rail.
- 8
Lay the plywood decks
Each deck is 30⅝″ × 23⅞″ and drops between two uprights (⅛″ of play), resting on the front and back rails. Good face up, factory edge to the front, flush with the front rail.
- Four #8 × 1⅝″ screws into each rail, about 2″ in from the ends of the deck.
- 8 decks total. If one is tight, plane or sand the end instead of forcing it: a forced deck pushes the uprights out of plumb.
Want a cleaner front edge? Glue on a strip of 1×2 later. It also stops round things rolling off. - 9
Done
4 shelves, 17″ clear between them, 72″ wide. Heavy stuff on the bottom two decks, light and bulky on top.
Each bay of ¾″ ply on 2×4 rails is good for a couple hundred pounds spread out. Point loads (an engine head, a full water jug) go near an upright, not mid-span.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
14 boards91% yieldSheet goods
- P Shelf deck, ¾″ plywood: 8 × 30⅝″ × 23⅞″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
Ladders every ≤48″ carry two long rails per shelf, screwed across the wide faces of the uprights; each plywood deck sits between the uprights on those rails, so nothing gets notched. Depth is overall, rail face to rail face. Screw the top back rail to the wall studs: a loaded shelf unit is top-heavy.