Garden Gate Builder
Shopping list
Pressure-treated 2×4 for the frame: it lives outside and near the ground. Standard 6′ dog-ear pickets, cedar or PT; pick the straightest ones in the stack.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8 pressure-treated | 2 | $4.98 | $9.96 |
| Dog-ear fence picket, ⅝″ × 5½″ × 6′ | 6 | $2.98 | $17.88 |
| Heavy-duty T-hinge, 8″, black (with screws) | 2 | $8.98 | $17.96 |
| Gravity gate latch | 1 | $9.98 | $9.98 |
| Gate pull handle, 8″ | 1 | $6.98 | $6.98 |
| Exterior screws, 2″, 1-lb box (frame and face boards) | 1 | $10.00 | $10.00 |
| Exterior screws, 2½″, 1-lb box (brace ends and hinges) | 1 | $11.00 | $11.00 |
| Total | $83.76 |
Tools: circular or miter saw, drill/driver, speed square, tape, a straightedge, two 1½″ spacer blocks, clamps, 4′ level, 2″ blocks and ½″ shims for setting the gate in the opening.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
2 boards65% yieldPicket × 6′
6 boards67% yieldThe diagonal brace always runs **up from the bottom hinge corner** to the top latch corner. That way it works in compression and holds the latch side up. Build it the other way and the gate sags in a season. Prices are per board at the price you enter.
- 1
Shopping list
Pressure-treated 2×4 for the frame: it lives outside and near the ground. Standard 6′ dog-ear pickets, cedar or PT; pick the straightest ones in the stack.
Item Qty Each Total 2×4×8 pressure-treated 2 $4.98 $9.96 Dog-ear fence picket, ⅝″ × 5½″ × 6′ 6 $2.98 $17.88 Heavy-duty T-hinge, 8″, black (with screws) 2 $8.98 $17.96 Gravity gate latch 1 $9.98 $9.98 Gate pull handle, 8″ 1 $6.98 $6.98 Exterior screws, 2″, 1-lb box (frame and face boards) 1 $10.00 $10.00 Exterior screws, 2½″, 1-lb box (brace ends and hinges) 1 $11.00 $11.00 Total $83.76 Tools: circular or miter saw, drill/driver, speed square, tape, a straightedge, two 1½″ spacer blocks, clamps, 4′ level, 2″ blocks and ½″ shims for setting the gate in the opening.
- 2
Cut list
Measure the opening at the top and bottom and use the smaller number. The gate is 40¾″ wide: ½″ clear on the hinge side, ¾″ on the latch side.
Tag Part Length Qty Cut R Rail (flat, top and bottom) 39¾″ 2 square B Diagonal brace 44⅞″ 1 50° off square both ends, parallel (level on the rails); scribe in place. Length is along either edge P Picket 48″ 6 cut from the bottom, keep the dog-ear Don't cut the brace from the list. Lay it across the frame in place, mark both ends where they cross the rails, and cut to the line. It should tap in snug. - 3
Lay out the face
Lay the 6 pickets face down with the bottoms flush against a straightedge and the dog-eared ends all at the top. Set the two outside pickets first, 40¾″ outside to outside, then space the rest evenly between them: the gaps come out about 1½″.
- The face that is down is the one the street sees, so put the better side of each picket down.
- Measure both diagonals. Equal means square.
- 4
Rails
Lay the two rails across the pickets, ½″ in from each side. Bottom rail 6″ up from the bottom, top rail 6″ down from the top so it sits below the dog-ears.
- Square each rail to the pickets with a speed square, then one 2″ screw down through the rail into each picket to hold the layout. That length stops just shy of the face.
- Pre-drill so the rail doesn't split near its ends.
- Decide the hinge side now. The model hinges on the left post as seen from the street; with the gate face down, that side is on your right.
- 5
Diagonal brace
Lay the brace across the frame from the bottom hinge corner to the top latch corner, about 40° from level. Mark where it crosses the inside edges of the rails, cut both ends, and tap it in snug between them. That's 50° off square, past most miter saws: cut it with a circular saw to the scribed line.
- Toe-screw each brace end into the rail with two 2½″ screws, and drive one 2″ screw down through the brace into every picket it crosses.
- Now flip the gate face up and drive two 2″ screws through every picket into each rail, plus one into the brace wherever it crosses. These face screws do the real holding; the ones from the back only bite ½″.
Upside-down brace = saggy gate. Check it twice before the first screw. - 6
Hang it
Set the gate in the opening on 2″ blocks with ½″ shims on the hinge side. Screw the two 8″ hinge straps to the back of the rails and the T-leaves to the back of the post.
- Level across the top before the post screws go in.
- Use the hinge's own screws in the gate; a 2½″ screw at each hinge's post end bites deeper.
- 7
Latch and handle
Mount the gravity latch bar on the back at the top of the latch side, then hold the keeper on the post and swing the gate shut to mark it. Screw on the pull at the same height on the front.
Push the gate shut a few times: the bar should ride up over the keeper and drop in on its own.
- 8
Done
A 40¾″ × 4′ gate. Seal or stain the end grain of every board, especially the bottoms.
If it ever sags, a turnbuckle anti-sag kit run opposite the brace (top hinge corner to bottom latch corner) pulls it back.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
2 boards65% yieldPicket × 6′
6 boards67% yieldThe diagonal brace always runs **up from the bottom hinge corner** to the top latch corner. That way it works in compression and holds the latch side up. Build it the other way and the gate sags in a season. Prices are per board at the price you enter.