Mudroom Bench Builder
Shopping list
Buy cabinet-grade birch or maple ply if it will be painted or clear-coated; sanded pine ply is fine under paint. Have the store rip one 18½″ strip for the seat and the rest into 16″ strips: it fits in the car and the long cuts come out straight.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8′ stud, untreated SPF | 5 | $3.50 | $17.50 |
| 2×6×8′, straightest you can find | 1 | $6.50 | $6.50 |
| ¾″ plywood, 4×8 sheet | 2 | $52.00 | $104.00 |
| #8 × 2″ wood screws, 1-lb box (plywood joints (or 1¼″ pocket screws)) | 1 | $10.00 | $10.00 |
| #8 × 2½″ wood screws, 1-lb box (toe kick) | 1 | $10.00 | $10.00 |
| Wood glue, 16 oz | 1 | $7.00 | $7.00 |
| Iron-on edge banding, ¾″ × 25′ | 2 | $11.00 | $22.00 |
| Paint or poly, 1 qt + primer | 1 | $32.00 | $32.00 |
| #10 × 3½″ wood screws, 1-lb box (~40) (cleat, ledger, rails and uprights into studs) | 1 | $11.98 | $11.98 |
| Coat hooks, double prong | 5 | $4.50 | $22.50 |
| Total | $243.48 |
Tools: circular saw with a straightedge guide (or table saw), drill/driver, pocket-hole jig (optional), stud finder, 4′ level, clamps, sander.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×6 × 8′
1 board86% yield2×4 × 8′
4 boards87% yieldSheet goods
- A End panel: 2 × 17¼″ × 16″
- B Bottom: 1 × 46½″ × 16″
- C Middle shelf: 1 × 46½″ × 16″
- E Divider: 6 × 6⅛″ × 16″
- S Seat top: 1 × 48″ × 18½″
- Q Top shelf: 1 × 50″ × 10″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
Cubbies are laid out about 11″ wide, a pair of adult shoes. The tall back is screwed to wall studs; never leave it free-standing. Prices are per board or sheet at the price you enter.
- 1
Shopping list
Buy cabinet-grade birch or maple ply if it will be painted or clear-coated; sanded pine ply is fine under paint. Have the store rip one 18½″ strip for the seat and the rest into 16″ strips: it fits in the car and the long cuts come out straight.
Item Qty Each Total 2×4×8′ stud, untreated SPF 5 $3.50 $17.50 2×6×8′, straightest you can find 1 $6.50 $6.50 ¾″ plywood, 4×8 sheet 2 $52.00 $104.00 #8 × 2″ wood screws, 1-lb box (plywood joints (or 1¼″ pocket screws)) 1 $10.00 $10.00 #8 × 2½″ wood screws, 1-lb box (toe kick) 1 $10.00 $10.00 Wood glue, 16 oz 1 $7.00 $7.00 Iron-on edge banding, ¾″ × 25′ 2 $11.00 $22.00 Paint or poly, 1 qt + primer 1 $32.00 $32.00 #10 × 3½″ wood screws, 1-lb box (~40) (cleat, ledger, rails and uprights into studs) 1 $11.98 $11.98 Coat hooks, double prong 5 $4.50 $22.50 Total $243.48 Tools: circular saw with a straightedge guide (or table saw), drill/driver, pocket-hole jig (optional), stud finder, 4′ level, clamps, sander.
- 2
Cut list
Plywood parts are 16″ wide, so the whole carcass comes from 16″ strips. Cut all strips first, then crosscut to length with a stop block so the dividers match.
Tag Part Length Qty Cut K1 Toe-kick rail (front/back) 46½″ 2 square K2 Toe-kick end / cross piece 10″ 3 square A End panel (16″ wide) 17¼″ 2 square B Bottom (16″ wide) 46½″ 1 square C Middle shelf (16″ wide) 46½″ 1 square E Divider (16″ wide) 6⅛″ 6 square S Seat top (18½″ wide) 48″ 1 square W Wall cleat 46½″ 1 square U Back upright 53¼″ 2 square G Top ledger 41″ 1 square J Shelf bracket 8″ 2 45° chamfer on the bottom front corner M Backrest rail (between uprights) 41″ 1 square N Hook rail (between uprights) 41″ 1 square Q Top shelf (10″ wide) 50″ 1 square Iron edge banding onto every plywood edge that faces out (front edges, seat front) before assembly. It is much easier on loose parts. - 3
Build the toe kick
The carcass sits on a 2×4 base set 3″ back from the front so your toes fit under. Two long rails, 3 short pieces between them, screwed through the rails into each end.
Set it on the floor where the bench will live and shim it level both ways. Everything above it inherits this.
- 4
Ends and bottom
Glue and screw the bottom (B) between the two end panels (A), resting on the toe kick. The ends run to the floor and hide the kick. 2″ screws through the ends every 6″, pilot-drilled so the ply edge doesn't split.
Screw down through the bottom into the kick from inside.
- 5
Shelf and dividers
Cut two scrap spacers at exactly 6⅛″. Stand them on the bottom, rest the middle shelf (C) on them (its underside ends up 10⅜″ off the floor), and glue and screw it through the ends with 2″ screws every 6″.
Dividers go in pairs, one below and one above the shelf, 11″ apart; work from one end with a 11″ spacer block (the last cubby comes out 11¼″). Glue each lower divider in, drive two 2″ screws down through the shelf into its top edge, and pin its bottom edge to the bottom with brads or a pocket screw. Glue each upper divider directly above it and pin it to the shelf the same way; the seat screws into the tops of the upper ones.
- 6
Seat and wall cleat
Find the studs. Level a 2×4 cleat on the wall with its top at 17¼″, and drive a 3½″ screw into every stud it crosses.
Push the bench back until it touches the cleat; it stands 1½″ off the wall, clear of the baseboard. Glue and screw the seat top down into the ends, dividers and cleat with 2″ screws; its back edge goes tight to the wall and it overhangs 1″ at the front.
The cleat is what keeps a kid standing on the front edge from tipping the bench. Don't skip it. - 7
Back uprights and ledger
First screw a shelf bracket (J) to the front face of each upright (U, 53¼″), centered and flush with the top: two 2½″ screws from the back of the upright into the bracket's end. Then stand the uprights on the seat at each back corner, flat to the wall, and fit the top ledger (G) between them, flush at the top.
Screw the ledger and each upright into wall studs (3½″ screws, two per stud), and pocket-screw or toe-screw the ledger ends to the uprights. Then the 2×6 backrest rail flat on the wall between the uprights, its bottom 6″ above the seat, two 3½″ screws into every stud.
If the uprights don't land on studs, use the ledger and hook rail as your stud anchors and toggle-bolt the uprights. Never rely on drywall anchors alone. - 8
Hook rail and top shelf
Fit the 2×6 hook rail flat on the wall between the uprights with its bottom edge 54″ off the floor: two 3½″ screws into every stud, a toe screw into each upright. Fit 5 hooks evenly along it, screwed into the rail, not just the drywall.
Then the 10″ top shelf, overhanging 1″ at each end: 2″ screws down into the ledger, the upright tops and the brackets.
- 9
Done
A 48″ bench with 8 cubbies, 5 hooks and a top shelf. Fill, sand and paint before loading it up; let paint cure a week before shoes go in.
Put a boot tray in the bottom row. Wet boots will ruin raw plywood edges in one winter.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×6 × 8′
1 board86% yield2×4 × 8′
4 boards87% yieldSheet goods
- A End panel: 2 × 17¼″ × 16″
- B Bottom: 1 × 46½″ × 16″
- C Middle shelf: 1 × 46½″ × 16″
- E Divider: 6 × 6⅛″ × 16″
- S Seat top: 1 × 48″ × 18½″
- Q Top shelf: 1 × 50″ × 10″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
Cubbies are laid out about 11″ wide, a pair of adult shoes. The tall back is screwed to wall studs; never leave it free-standing. Prices are per board or sheet at the price you enter.