Patio Sofa Builder
Shopping list
All 2×4, all pressure-treated (or cedar if it lives under a roof). Cushions go on the list too: buy them before cutting anything. These dimensions assume 24″ × 24″ seat cushions about 5″ thick.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8′ pressure-treated | 19 | $4.98 | $94.62 |
| #9 × 3″ exterior screws, 5-lb box (~350) (about 144 screws) | 1 | $34.98 | $34.98 |
| #9 × 2½″ exterior screws, 1-lb box (~75) (face-to-face joints (side rails to posts, feet to joists), about 24) | 1 | $10.98 | $10.98 |
| Exterior wood glue, 16 oz | 1 | $8.98 | $8.98 |
| Deep-seat outdoor cushion set (seat + back), 24″ (optional; buy first) | 3 | $89.98 | $269.94 |
| Exterior stain / sealer, 1 gal (optional) | 1 | $38.98 | $38.98 |
| Total | $458.48 |
Tools: miter saw, impact driver, drill with ⅛″ pilot bit, clamps (at least two 24″), speed square, 4′ level, sander.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
18 boards87% yieldSeat deck at 13″; with a 5″ cushion you sit at about 17″, deep-seating height. Arms at 24″, back at 30″. Prices are per 8′ board at the price you enter.
- 1
Shopping list
All 2×4, all pressure-treated (or cedar if it lives under a roof). Cushions go on the list too: buy them before cutting anything. These dimensions assume 24″ × 24″ seat cushions about 5″ thick.
Item Qty Each Total 2×4×8′ pressure-treated 19 $4.98 $94.62 #9 × 3″ exterior screws, 5-lb box (~350) (about 144 screws) 1 $34.98 $34.98 #9 × 2½″ exterior screws, 1-lb box (~75) (face-to-face joints (side rails to posts, feet to joists), about 24) 1 $10.98 $10.98 Exterior wood glue, 16 oz 1 $8.98 $8.98 Deep-seat outdoor cushion set (seat + back), 24″ (optional; buy first) 3 $89.98 $269.94 Exterior stain / sealer, 1 gal (optional) 1 $38.98 $38.98 Total $458.48 Tools: miter saw, impact driver, drill with ⅛″ pilot bit, clamps (at least two 24″), speed square, 4′ level, sander.
- 2
Cut list
Everything is square-cut 2×4. Gang-cut identical parts against a stop block so both ends of every run come out the same.
Tag Part Length Qty Cut A Arm rail (on the flat) 23″ 2 square B Back slat 78″ 5 square D Deck slat (on the flat) 75″ 6 square F Center foot 11½″ 4 square J Seat joist 22″ 2 square K Back stiffener 30″ 2 square P Back post 30″ 2 square P Front post, arm end 22½″ 2 square R Front / back seat rail 72″ 2 square R Seat side rail 25″ 2 square S Side / arm slat 26½″ 6 square - 3
End frames
Each end of each section is a front post, a 30″ back post, and a 25″ seat side rail screwed to the inside face, 8″ off the floor.
- Arm ends: front post 22½″, so the arm rail lands at 24″.
- Glue plus three 2½″ screws per joint, in a triangle (two 2×4s face to face are 3″ thick, so a 3″ screw would come out the far side). Check each frame square. The glue matters: this joint is what holds the back post upright.
- 4
Seat frame
Stand two end frames up and join them with front and back seat rails between the side rails, tops flush.
- Joists front to back at every cushion seam (every 24″), between the rails. One 11½″ foot stands against one face of each joist at each end, tight inside the rail and top flush with the joist, so the middle can't sag: glue plus three 2½″ screws through the foot into the joist, and two 3″ screws through the rail into the foot's edge.
- Two 3″ screws through the rails into each joist end.
- Diagonals across the seat frame must match. This is the step that decides whether it rocks.
- 5
Seat deck
6 2×4 slats on the flat, running side to side across the joists, about ¾″ apart so rain drains out from under the cushions.
Two 3″ screws into every side rail and joist. First slat flush with the back face of the back rail (it butts the back posts), last one flush with the front.
- 6
Back, sides and arms
5 back slats across the back face of the back posts, 8″ to 30″; the bottom one covers the back seat rail. A 2×4 stiffener stands on edge behind the slats at each cushion seam, down to the floor; screw through every slat into its edge. Screw the bottom slat into the back rail between the posts as well; that is what ties the back to the seat.
- Arm ends: 3 side slats on the outside face, then a 2×4 arm rail on the flat on top, butted into the back post. Round its front corners.
- Two 3″ screws per slat at every post and stiffener.
- 7
Done
3 seats. Drop in the cushions: seat cushions on the deck, back cushions standing against the back slats.
Drill a few ½″ holes through the deck slats at the low spots if water pools. Store the cushions in a deck box when it rains; the frame doesn't care, the foam does.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
18 boards87% yieldSeat deck at 13″; with a 5″ cushion you sit at about 17″, deep-seating height. Arms at 24″, back at 30″. Prices are per 8′ board at the price you enter.