Planter Box Builder
Shopping list
Cedar sides because they touch wet soil and look good for a decade. The 2×4 posts, cleats and caps can be treated pine; if you're growing food, line the inside walls with landscape fabric so treated wood never touches the soil. Totals cover all 2.
| Item | Qty | Each | Total |
|---|---|---|---|
| Cedar 2×6×8′ (sides and floor) | 8 | $14.98 | $119.84 |
| 2×4×8′ pressure-treated (or cedar) (posts, cleats, caps) | 5 | $4.98 | $24.90 |
| #9 × 2½″ exterior screws, star drive, 1-lb box (~75) (about 102 per planter) | 3 | $10.98 | $32.94 |
| Landscape fabric, 3′ × 50′ (150 ft²) (liner, about 30 ft² with overlaps) | 1 | $12.98 | $12.98 |
| Potting mix, 1.5 ft³ bag (6.1 ft³ total) | 5 | $9.97 | $49.85 |
| Total | $240.51 |
Tools: miter saw, drill/driver with T25 bit, ⅛″ pilot bit, speed square, clamps, staple gun.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×6 × 8′
8 boards87% yield2×4 × 8′
5 boards80% yieldBox heights are in whole 2×6 courses (5½″ each). Floor slats leave ½″–1″ drainage gaps. Prices are per 8′ board at the price you enter; longer boards are priced pro rata.
- 1
Shopping list
Cedar sides because they touch wet soil and look good for a decade. The 2×4 posts, cleats and caps can be treated pine; if you're growing food, line the inside walls with landscape fabric so treated wood never touches the soil. Totals cover all 2.
Item Qty Each Total Cedar 2×6×8′ (sides and floor) 8 $14.98 $119.84 2×4×8′ pressure-treated (or cedar) (posts, cleats, caps) 5 $4.98 $24.90 #9 × 2½″ exterior screws, star drive, 1-lb box (~75) (about 102 per planter) 3 $10.98 $32.94 Landscape fabric, 3′ × 50′ (150 ft²) (liner, about 30 ft² with overlaps) 1 $12.98 $12.98 Potting mix, 1.5 ft³ bag (6.1 ft³ total) 5 $9.97 $49.85 Total $240.51 Tools: miter saw, drill/driver with T25 bit, ⅛″ pilot bit, speed square, clamps, staple gun.
- 2
Cut list
Long sides run full length; short sides fit between them. Corner posts are the full box height, 16½″.
Tag Part Length Qty Cut S Long side, cedar 2×6 24″ 12 square E Short side, cedar 2×6 21″ 12 square F Floor slat, cedar 2×6 21″ 6 square P Corner post, 2×4 16½″ 8 square C Floor cleat, 2×4 flat 18″ 4 square T Long cap, 2×4 flat 25½″ 4 square T Short cap, 2×4 flat 18½″ 4 square - 3
Corner posts
Four 16½″ 2×4 posts, one in each inside corner. Stand them on a flat surface; you'll screw the sides on around them.
Building several? Cut every part for every box first, then assemble production-line style. - 4
First course
Long sides overlap the short sides at the corners. Set the first course flat on the bench, and screw:
- Two screws through each long side into the end grain of the short side.
- Two screws through each board into the post behind it: the long side into its edge, the short side into its face.
- Pre-drill everything within 1″ of an end. Cedar splits.
Check: diagonals match before the second course locks it in. - 5
Stack the remaining courses
2 more courses, tight on top of the first, same screw pattern, staggered so you don't hit the screws below.
Check the top is flat with a straightedge across the corners. Plane or sand a proud board now; the cap hides nothing.
- 6
Floor
Two flat 2×4 cleats along the bottom inside the long sides, between the posts. 3 cedar floor slats across them, about ¾″ apart for drainage.
- Cleats: bottom flush with the bottom of the first course; a 2½″ screw through the side into the cleat every 6″.
- Slats: two screws into each cleat. They stop at the posts, leaving a 1½″ slot along each end wall; the fabric liner covers it.
- On the ground the cleats hold the slats 1½″ up, so water drains out under the box instead of pooling in it. Set it on pavers or gravel, not bare soil.
- 7
Cap
A flat 2×4 cap all the way around, overhanging the outside by ¾″. Long caps run full length; short caps fit between.
- 2½″ screws down through the cap into the post tops and the top board, every 8″.
- Sand the cap corners round. It becomes a bench for your coffee.
- 8
Done
Staple landscape fabric up the inside walls and over the floor, then fill with potting mix to 1½″ below the rim: 3.1 ft³ per box.
Planters dry out faster than beds. A drip line or a daily check in summer; a 2″ layer of mulch on top helps.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×6 × 8′
8 boards87% yield2×4 × 8′
5 boards80% yieldBox heights are in whole 2×6 courses (5½″ each). Floor slats leave ½″–1″ drainage gaps. Prices are per 8′ board at the price you enter; longer boards are priced pro rata.