Potting Bench Builder
Shopping list
It lives outside and gets watered every day: buy pressure-treated or cedar, and exterior-rated screws. Pick the straightest boards for the legs; the slats can be a little crooked.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8′ pressure-treated (frame) | 6 | $4.98 | $29.88 |
| 2×6×8′ pressure-treated (slats, back, shelf) | 8 | $7.98 | $63.84 |
| #9 × 3″ exterior screws, 1-lb box (~55) (aprons and back boards, about 38) | 1 | $10.98 | $10.98 |
| #9 × 2½″ exterior screws, 1-lb box (~75) (end frames, slats and shelf, about 94) | 2 | $10.98 | $21.96 |
| Exterior wood glue, 8 oz | 1 | $5.98 | $5.98 |
| S-hooks for the top rail (optional) | 6 | $0.98 | $5.88 |
| Total | $138.52 |
Tools: miter saw or circular saw + speed square, drill/driver, clamps, tape, 4′ level, a ¼″ spacer for the backsplash boards, and a scrap ripped to the slat gap.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×6 × 8′
8 boards80% yield2×4 × 8′
6 boards87% yieldThe work surface is 24″ deep plus the aprons. Slats run front to back so soil and water fall straight through. Prices are per 8′ board at the price you enter.
- 1
Shopping list
It lives outside and gets watered every day: buy pressure-treated or cedar, and exterior-rated screws. Pick the straightest boards for the legs; the slats can be a little crooked.
Item Qty Each Total 2×4×8′ pressure-treated (frame) 6 $4.98 $29.88 2×6×8′ pressure-treated (slats, back, shelf) 8 $7.98 $63.84 #9 × 3″ exterior screws, 1-lb box (~55) (aprons and back boards, about 38) 1 $10.98 $10.98 #9 × 2½″ exterior screws, 1-lb box (~75) (end frames, slats and shelf, about 94) 2 $10.98 $21.96 Exterior wood glue, 8 oz 1 $5.98 $5.98 S-hooks for the top rail (optional) 6 $0.98 $5.88 Total $138.52 Tools: miter saw or circular saw + speed square, drill/driver, clamps, tape, 4′ level, a ¼″ spacer for the backsplash boards, and a scrap ripped to the slat gap.
- 2
Cut list
Two tall back legs and two short front legs. Slats for both decks are the same 27″, so set a stop block once and cut all 14.
Tag Part Length Qty Cut F Front leg, 2×4 36″ 2 square B Back leg, 2×4 60″ 2 square R Side rail, 2×4 (top + bottom, each end) 24″ 4 square A Apron / stretcher, 2×4 (front + back, top + bottom) 48″ 4 square S Slat, 2×6 (work surface + lower shelf) 27″ 14 square K Backsplash + top rail, 2×6 48″ 3 square H Upper shelf board, 2×6 45″ 2 square C Shelf cleat, 2×4 11¼″ 2 45° off the bottom front corner - 3
Build the two end frames
Each end is one short front leg (36″), one tall back leg (60″), and two 24″ side rails screwed to the inside face.
- Top rail: its top edge 1½″ below the top of the front leg, so the slats land flush with the leg at 36″.
- Bottom rail: 6½″ off the floor.
- Rails flush with the front edge of the front leg and the back edge of the back leg. Glue plus three 2½″ screws per joint, in a triangle (3″ screws would come out the far side of two 2×4s).
Build the second frame as a mirror image on top of the first so they come out identical. - 4
Aprons and stretchers
Stand the end frames up, rails facing in, 48″ apart over the outside faces of the legs. Four 48″ 2×4s on edge run full length across the front and back faces of the legs, at the same heights as the side rails.
- Two 3″ screws into each leg, plus one into the end grain of the side rail.
- Measure both diagonals of the top rectangle; rack it until they match, then drive the last screws.
- 5
Lower shelf slats
7 slats front to back across the lower stretchers, flush with the front and back faces. First and last ones tight to the legs; spread the rest evenly, roughly 1⅛″ apart.
Two 2½″ screws in each slat end. This shelf carries bags of potting mix, so don't skip screws.
- 6
Work surface
Same layout on top: 7 slats over the aprons, tops flush with the front leg tops at 36″.
- Lay them all out with spacers before screwing any.
- Pre-drill slat ends within 1½″ of the end so they don't split.
- Ease the front edge with sandpaper or a ¼″ roundover; your forearms will rest on it.
- 7
Backsplash and top rail
2 2×6s across the back face of the back legs, starting tight on the work surface, ¼″ apart. One more at the very top of the back legs as a tool rail.
- Two 3″ screws at each leg, predrilled.
- Level the first board; the rest follow it.
- S-hooks on the top rail hold trowels, gloves, and a hose nozzle.
- 8
Upper shelf
Glue and screw a 11¼″ cleat (on edge, running front to back) to the inside face of each back leg with three 2½″ screws in a triangle, top edge 51½″ off the floor and back end flush with the back of the leg. Lay two 45″ shelf boards on the cleats between the legs: the back one flush with the back of the legs, the front one ¼″ in front of it. The shelf top lands at 53″, 1½″ under the top rail.
- Clip the bottom front corner of each cleat at 45° so it doesn't catch your head.
- Two 2½″ screws through each end of each board into the cleat, plus a 3″ screw through each back leg into the end of the back shelf board.
- The cleats cantilever off the legs, so this is a light-duty shelf: seed trays, hand tools and small pots, about 25 lb total.
- 9
Done
A 4′ potting bench at 36″. Water runs straight through the slats, and the lower shelf holds 2–3 bags of mix.
Set the feet on pavers or a gravel pad so the legs aren't sitting in wet soil. Clip a 5-gallon bucket under one end of the work surface as a soil catch.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×6 × 8′
8 boards80% yield2×4 × 8′
6 boards87% yieldThe work surface is 24″ deep plus the aprons. Slats run front to back so soil and water fall straight through. Prices are per 8′ board at the price you enter.