Tire Rack Builder
Shopping list
Plain SPF studs are fine indoors. The brackets hang on wall studs 32″ apart, so the lag screws, not the drywall, carry the load: about 240 lb if the tires are stored on their wheels.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8 stud, SPF | 4 | $3.50 | $14.00 |
| ⅜″ × 6″ hex lag screw with washer (uprights to studs) | 4 | $1.45 | $5.80 |
| ⅜″ × 5½″ carriage bolt with washer and nut (3 per bracket: two through the arms and upright, one through the brace) | 6 | $1.20 | $7.20 |
| #9 × 3″ construction screws, 1-lb box (about 20: rails and brace feet) | 1 | $10.00 | $10.00 |
| Total | $37.00 |
Tools: miter or circular saw, drill/driver, stud finder, 4′ level, ¼″ and ⅜″ bits, socket wrench, clamps, tape.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
4 boards78% yieldTires store best standing up, not stacked, and off bare concrete. The two rails cradle each tire so it can't roll. Size for your biggest tire; smaller ones fit fine. Prices are per board at the price you enter.
- 1
Shopping list
Plain SPF studs are fine indoors. The brackets hang on wall studs 32″ apart, so the lag screws, not the drywall, carry the load: about 240 lb if the tires are stored on their wheels.
Item Qty Each Total 2×4×8 stud, SPF 4 $3.50 $14.00 ⅜″ × 6″ hex lag screw with washer (uprights to studs) 4 $1.45 $5.80 ⅜″ × 5½″ carriage bolt with washer and nut (3 per bracket: two through the arms and upright, one through the brace) 6 $1.20 $7.20 #9 × 3″ construction screws, 1-lb box (about 20: rails and brace feet) 1 $10.00 $10.00 Total $37.00 Tools: miter or circular saw, drill/driver, stud finder, 4′ level, ¼″ and ⅜″ bits, socket wrench, clamps, tape.
- 2
Cut list
Rails are 46″: 4 tires at 10″ wide plus an inch of breathing room each. The braces are the only angled cuts.
Tag Part Length Qty Cut U Upright (on edge, narrow face to the wall, over a stud) 21½″ 2 square A Arm (on edge, pairs sandwich the upright) 29″ 4 square B Brace (between the arm pair) 23¼″ 2 45° both ends, mitered opposite ways so the piece is a trapezoid (one end sits plumb, the other level); length is the long edge R Rail (flat, tires stand on two) 46″ 2 square Cut one brace, hold it in place between an arm pair to check the fit, then cut the other 1 to match. - 3
Hang the uprights
Find 2 studs 32″ apart and mark their centers. Stand an upright on edge (narrow face to the wall) centered on each one, sitting on the floor, and plumb it.
- Mark the arm bottoms at 14″ off the floor. For each one, 5″ below and 5½″ above that mark, drill a ⅜″ hole through the upright only, then a ¼″ pilot on into the stud, and drive a ⅜″ × 6″ lag with a washer. A 6″ lag passes through the 3½″ upright and the drywall and still bites 2″ into the stud.
- Carry each arm-bottom mark across all the uprights with the level.
- 4
Bolt on the arms
Each bracket gets a pair of 29″ arms on edge, one on each side of the upright, back ends tight to the wall, bottoms on your level line.
- Clamp, check level front-to-back, then drill two ⅜″ holes on a diagonal through arm–upright–arm (about 1″ in from opposite corners of the overlap) and bolt them tight with carriage bolts.
- Keep every pair at the same height so the rails sit flat.
- 5
Braces
A 45° brace (23¼″ on its long edge, long edge down) slides up between each arm pair: plumb end bearing flat on the front edge of the upright, level end flush with the arm tops. Its short upper edge meets the upright 8″ below the arm.
- Clamp it, then bolt through arm–brace–arm near the top with one more ⅜″ carriage bolt.
- Two 3″ screws angled through the brace foot into the upright keep it from sliding. Each bracket carries up to about 120 lb.
- 6
Rails
Two rails per tier, laid flat across the arms with 9½″ of open space between them. The tire settles into that gap and can't roll.
- Rail ends overhang the outer brackets equally. Two 3″ screws down through each rail into every arm.
- Keep the gap even; a scrap block cut to the gap is a quick spacer.
- 7
Done
Room for 4 tires. Stand each one upright in the cradle, tread down.
- Wash and dry the tires before storing; brake dust eats rubber.
- Bag them in tire totes to keep ozone off, and keep the rack away from the water heater and any electric motors.
Rotate stored tires a quarter turn every month or so to avoid flat spots.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
4 boards78% yieldTires store best standing up, not stacked, and off bare concrete. The two rails cradle each tire so it can't roll. Size for your biggest tire; smaller ones fit fine. Prices are per board at the price you enter.