Rolling Tool Cart Builder
Shopping list
Get casters rated for at least 100 lb each, two swivel with brakes and two fixed (or four locking swivels if you'll push it sideways a lot). Plate-mount, not stem.
| Item | Qty | Each | Total |
|---|---|---|---|
| 2×4×8′ stud, untreated SPF | 7 | $3.50 | $24.50 |
| ¾″ plywood, 4×8 sheet | 1 | $52.00 | $52.00 |
| 3″ plate caster, locking swivel | 2 | $13.00 | $26.00 |
| 3″ plate caster, rigid | 2 | $9.00 | $18.00 |
| ¼″ × 1½″ lag screws + washers (casters) | 16 | $0.40 | $6.40 |
| #9 × 3″ construction screws, 1-lb box (rail frames, end rails into legs) | 1 | $10.00 | $10.00 |
| #9 × 2½″ construction screws, small box (long rails into legs, grip) | 1 | $7.00 | $7.00 |
| #8 × 1¼″ wood screws, small box (shelves, top, caster pads) | 1 | $6.00 | $6.00 |
| Wood glue, 8 oz | 1 | $5.00 | $5.00 |
| ⅜″ × 6″ hex lag screws + washers (handle) | 6 | $1.45 | $8.70 |
| Total | $163.60 |
Tools: circular saw with a straightedge, jigsaw for the leg holes, drill/driver, ¼″ and ⅜″ bits, socket set, speed square, clamps, a router or rasp to round the grip.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
6 boards97% yieldSheet goods
- E Shelf, with four 3½ × 1½″ leg holes: 2 × 36″ × 24″
- F Top: 1 × 36″ × 24″
- G Caster pad: 4 × 5″ × 5″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
Height is to the top surface, including 3″ casters (4″ mounting height; adjust the legs if yours differ). The legs pass through holes in the shelves, so the shelves sit on the rails, not on screws. Prices are per board or sheet at the price you enter.
- 1
Shopping list
Get casters rated for at least 100 lb each, two swivel with brakes and two fixed (or four locking swivels if you'll push it sideways a lot). Plate-mount, not stem.
Item Qty Each Total 2×4×8′ stud, untreated SPF 7 $3.50 $24.50 ¾″ plywood, 4×8 sheet 1 $52.00 $52.00 3″ plate caster, locking swivel 2 $13.00 $26.00 3″ plate caster, rigid 2 $9.00 $18.00 ¼″ × 1½″ lag screws + washers (casters) 16 $0.40 $6.40 #9 × 3″ construction screws, 1-lb box (rail frames, end rails into legs) 1 $10.00 $10.00 #9 × 2½″ construction screws, small box (long rails into legs, grip) 1 $7.00 $7.00 #8 × 1¼″ wood screws, small box (shelves, top, caster pads) 1 $6.00 $6.00 Wood glue, 8 oz 1 $5.00 $5.00 ⅜″ × 6″ hex lag screws + washers (handle) 6 $1.45 $8.70 Total $163.60 Tools: circular saw with a straightedge, jigsaw for the leg holes, drill/driver, ¼″ and ⅜″ bits, socket set, speed square, clamps, a router or rasp to round the grip.
- 2
Cut list
Every rail rectangle is identical: two 36″ long rails with 21″ end rails between them. Cut all 12 rails first with stop blocks.
Tag Part Length Qty Cut A Long rail (front/back) 36″ 6 square B End rail 21″ 6 square C Leg 28½″ 4 square E Shelf, with four 3½ × 1½″ leg holes (24″ wide) 36″ 2 square F Top (24″ wide) 36″ 1 square G Caster pad (5″ wide) 5″ 4 from the offcut strip U Handle upright 37¼″ 2 square; round the top K Handle grip 24″ 1 square; round over all 4 long edges and the ends Each shelf gets four leg holes, 3½ × 1½″, set 1½″ in from the end and 1½″ in from the long edge (long side of the hole along the long edge). Check the layout against a finished rail frame, drill a ⅜″ starter hole in two opposite corners of each, and cut with a jigsaw a hair oversize. - 3
Build the rail frames
Make 3 identical rectangles: 2×4s on edge, long rails outside, end rails between. Glue and two 3″ screws through the long rail into each end rail.
Check each one by its diagonals. If the frames match, the cart will be square without fighting it later. The picture shows the bottom frame; the others go on in step 5.
- 4
Legs and bottom shelf
With the bottom frame on a flat floor, stand a leg (28½″) inside each corner, wide face against the long rail, edge tight to the end rail, bottom flush with the bottom of the frame.
Glue, then two 3″ screws through the end rail into the leg's edge and two 2½″ screws through the long rail into its face. Clamp a square to the leg while you drive them.
Drop the bottom shelf over the four legs onto the frame. Glue and 1¼″ screws every 8″ into the rails.
- 5
Middle shelf, top frame and top
Slide the middle frame down over the legs until its top edge is 16″ above the leg bottoms (20¾″ off the floor once the casters are on). Rest it on four scrap blocks cut to 8¼″ standing on the bottom shelf, then screw it to the legs the same way and drop the middle shelf on.
Fit the last frame flush with the leg tops and screw it to the legs: 3″ through the end rails, 2½″ through the long rails.
The top is a full panel over the leg tops and top rails. Glue it and screw it down with 1¼″ screws every 8″; it's what keeps the cart from racking.
- 6
Caster pads and casters
Flip the cart over. Glue and screw a 5″ plywood pad under each corner with 1¼″ screws, covering the leg end and both rails.
- Locking swivels at the handle end (the left end in the picture), rigid casters at the other: it steers like a shopping cart.
- Pre-drill and drive four ¼″ lag screws through each caster plate.
Lags through the pad into the rails and the leg end hold far better than wood screws. Don't skip the pads. - 7
Push handle
Clamp the two handle uprights (37¼″) to the outside of the end rail at the swivel-caster end, flush with the front and back faces of the cart and with the bottom of the bottom rail. They stand 8″ above the top.
At each rail level, drill a ⅜″ clearance hole through the upright and end rail 2¼″ in from the cart's edge, then a ¼″ pilot into the leg behind it, and drive a ⅜″ × 6″ lag with a washer (3 per upright). The lags bite 3″ into the leg.
Round over the 24″ grip, then glue and screw it across the outside faces of the uprights, flush with their tops, two 2½″ screws into each. Pushing presses it straight into the uprights.
- 8
Done
A 24 × 36″ cart, 34″ to the top, 3 levels. Lock the brakes before you use it as a work surface.
Screw a power strip to a leg and hang a few hooks on the end rails; it becomes the most useful thing in the shop.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
2×4 × 8′
6 boards97% yieldSheet goods
- E Shelf, with four 3½ × 1½″ leg holes: 2 × 36″ × 24″
- F Top: 1 × 36″ × 24″
- G Caster pad: 4 × 5″ × 5″
Rip sheet parts on a table saw or with a circular saw and a straightedge; most stores will make the first rips for free.
Height is to the top surface, including 3″ casters (4″ mounting height; adjust the legs if yours differ). The legs pass through holes in the shelves, so the shelves sit on the rails, not on screws. Prices are per board or sheet at the price you enter.