Trash Enclosure Builder
Shopping list
Everything here is ground-contact or close to it, so buy pressure-treated framing. Pickets are standard ⅝″ × 5½″ × 6′ dog-ears; cedar or treated pine both work. The lids take a beating from wind; the T-hinges matter more than the wood.
| Item | Qty | Each | Total |
|---|---|---|---|
| 4×4×8′ pressure-treated (posts) | 6 | $11.98 | $71.88 |
| 2×4×8′ pressure-treated (rails) | 8 | $4.98 | $39.84 |
| Fence picket ⅝″ × 5½″ × 6′ | 45 | $2.98 | $134.10 |
| #9 × 3″ exterior screws, 1-lb box (~55) (frame, about 48) | 1 | $10.98 | $10.98 |
| #8 × 1⅝″ exterior screws, 1-lb box (~140) (pickets, 4 each, about 180) | 2 | $9.98 | $19.96 |
| 4×4 post base (ABA44-type) + ½″ × 4¼″ wedge anchor | 6 | $15.48 | $92.88 |
| #9 × 1½″ structural connector screws, 100-pack (post bases) | 1 | $18.98 | $18.98 |
| 6″ galvanized T-hinge | 4 | $6.98 | $27.92 |
| Lid stay chain kit (or 2′ of chain + 2 eye screws) | 2 | $5.48 | $10.96 |
| Gate pull handle | 2 | $4.98 | $9.96 |
| Total | $437.46 |
Tools: miter or circular saw, drill/driver, impact driver, hammer drill with masonry bit (for the anchors), 4′ level, speed square, tape, clamps.
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
4×4 × 8′
6 boards54% yield2×4 × 8′
8 boards68% yieldPicket × 6′
45 boards67% yieldBays are sized from typical city carts: 96-gal ≈ 29″ × 35″ × 46″, 64-gal ≈ 25″ × 31″ × 42″. Measure yours before you cut. Prices are per 8′ board (per 6′ picket) at the price you enter.
- 1
Shopping list
Everything here is ground-contact or close to it, so buy pressure-treated framing. Pickets are standard ⅝″ × 5½″ × 6′ dog-ears; cedar or treated pine both work. The lids take a beating from wind; the T-hinges matter more than the wood.
Item Qty Each Total 4×4×8′ pressure-treated (posts) 6 $11.98 $71.88 2×4×8′ pressure-treated (rails) 8 $4.98 $39.84 Fence picket ⅝″ × 5½″ × 6′ 45 $2.98 $134.10 #9 × 3″ exterior screws, 1-lb box (~55) (frame, about 48) 1 $10.98 $10.98 #8 × 1⅝″ exterior screws, 1-lb box (~140) (pickets, 4 each, about 180) 2 $9.98 $19.96 4×4 post base (ABA44-type) + ½″ × 4¼″ wedge anchor 6 $15.48 $92.88 #9 × 1½″ structural connector screws, 100-pack (post bases) 1 $18.98 $18.98 6″ galvanized T-hinge 4 $6.98 $27.92 Lid stay chain kit (or 2′ of chain + 2 eye screws) 2 $5.48 $10.96 Gate pull handle 2 $4.98 $9.96 Total $437.46 Tools: miter or circular saw, drill/driver, impact driver, hammer drill with masonry bit (for the anchors), 4′ level, speed square, tape, clamps.
- 2
Cut list
Posts are full 4×4s, all 52″. Rails run between posts. Wall pickets are all the same 51″: 1″ shorter than the posts, so they hang 1″ clear of the pad and never sit in standing water.
Tag Part Length Qty Cut P Post, 4×4 52″ 6 square R Back rail + front header, 2×4 33″ 6 square S Side / divider rail, 2×4 32⅜″ 6 square K Wall picket 51″ 33 trim dog-ear off or keep on top L Lid picket 41″ 12 square both ends C Lid cleat, 2×4 flat 31½″ 4 square Gang-cut the 33 wall pickets: clamp four together against a stop block and cut once. - 3
Set the posts
Lay out 6 posts on your pad: 3 along the back, 3 along the front, 33″ clear between neighbors and 39⅜″ front-to-back outside to outside.
- Bolt a post base at each spot with a ½″ wedge anchor (hammer drill, ½″ masonry bit, drilled ½″ deeper than the anchor's embedment, about 3½″). Blow the dust out before you tap the anchor in. Stand the posts in the bases and fill every hole in each base with the structural screws. The bases hold the post ends 1″ off the concrete, so the finished enclosure stands 1″ taller than the post length; every height in this manual is measured from the bottom of the posts.
- Check every post for plumb on two adjacent faces. Diagonals across the whole footprint should match.
No slab? Pour a 4″ pad first, or set a precast concrete pier block under each post, leveled in 4″ of compacted gravel, and fasten the posts to those. Don't bury these posts: they're cut to stand on top of the ground. - 4
Rails and front header
Two 2×4 rails on edge in every wall: bottom rail 4″ off the ground, top rail flush with the post tops. Divider rails sit flush with the right face of each middle post so the pickets lay flat.
- Back rails sit flush with the back face of the posts; end rails flush with the outside face.
- A header across the front of each bay at the top, flush with the front. It's what keeps the front posts from spreading, and it's the lid stop.
- Two 3″ screws per rail end, toe-screwed or through a pocket hole. Pre-drill near the ends.
Check: clamp a level across each top rail. Shim under a post now, not after the pickets are on. - 5
Back pickets
13 pickets across the back, 1″ off the ground, tops flush with the posts. Start flush at one end and work across, ⅜″ apart; the last one lands flush at the far end.
- Two 1⅝″ screws into each rail per picket. Cut a spacer block to the gap and use it between every pair.
- Hold a level on the first picket. Every one after it follows that one.
- 6
Side and divider pickets
14 pickets on the two ends, covering the back picket edges, front edge flush with the front of the posts. Then 6 on the divider walls (on the right face of each middle post and its rails, starting just in front of the back rail and stopping just behind the front header) so bins don't bang together.
- Same 1″ ground gap; about ¼″ between pickets.
- Pre-drill near the picket ends so they don't split.
- 7
Build and hang the lids
Each lid is 6 pickets on two flat 2×4 cleats, 36″ wide overall with about ⅝″ between pickets. Build them upside down on a flat surface, then flip.
- Cleats are 31½″ long, centered on the lid's width, and sit inside the bay: the back cleat 2⅜″ in from the lid's back edge (just in front of the back rail), the front cleat 2¾″ in from the front edge (just behind the header). That's what keeps the lid from sliding.
- Two 1⅝″ screws per picket into each cleat. Check the lid is square by its diagonals before the last screws.
- Set each lid on top, back edge flush with the back pickets and 1″ overhanging the front. Two T-hinges per lid: strap on top of the lid with its screws going through the picket into the back cleat, leaf on the back face of the back pickets, screwed through into the top rail. Add a stay chain so the lid stops just past vertical.
- Pull handle on the front edge.
Lift the enclosure lid, then the cart lid. With 6″ of headroom, the cart lid opens fully once the enclosure lid is up. - 8
Done
2 bays for 96-gal carts, 33″ clear each. Roll the carts in handle-out so pickup day is grab-and-go.
Stain or seal the pickets after a month of drying. Treated framing doesn't need it, but the pickets will cup less. A rubber bumper on the back rail saves the pickets from cart handles.
Cut diagram
Every cut laid onto standard boards, longest first, with a ⅛″ saw kerf between pieces. Hatched space at the end of a board is offcut, and ×3 means cut three boards the same way. Use this at the saw to cut one board at a time.
4×4 × 8′
6 boards54% yield2×4 × 8′
8 boards68% yieldPicket × 6′
45 boards67% yieldBays are sized from typical city carts: 96-gal ≈ 29″ × 35″ × 46″, 64-gal ≈ 25″ × 31″ × 42″. Measure yours before you cut. Prices are per 8′ board (per 6′ picket) at the price you enter.